Change CC number in Midi map list (when using an XY pad controller).

Hello,

Is it possible to edit the CC number in the midi map list manually?

For example, click on a mapping then type it in.

 

Context:
I have an XY controller joystick and XY controller pad.
Both axis send a different CC number.

The problem is that it is very difficult to only trigger 1 axis when moving the joystick or pad. This means invariably when you try to use midi map, both the X and Y axis CC controls are mapped to the same device control.

The easiest solution would be that you can manually edit the CC number in the midi map list after you have mapped it.

Of course, I could temporarily disable one axis, but that interrupts my workflow greatly (loading the editor software for the controllers, transmitting).

19 followers

jrs1 4 years ago | 0 comments

13 answers

  • mattb
    contribution
    3 answers
    6 votes received
    4 votes

    hey, just messing with the new HotHand xyz controller...assigning them in live is a pain because you cant edit ccs.

    whats the problem with just being able to manually edit cc numbers in the midi mappings page?

    would be handy ...Live is normally so good at supporting what we need to experiment, so please consider this.

     

    thanks

     

    1 year ago | 0 comments
  • Mattijs
    contribution
    2 answers
    5 votes received
    4 votes

    Hi, 

    I agree that this is a very weird oversight. 

    I don't see why the Midi Mappings window does not support changing the channels / cc's.

    Hope this can be fixed in a future version.

    1 year ago | 0 comments
  • garyboozy
    contribution
    6 answers
    12 votes received
    2 votes

    When in map mode, use 'undo' to go back through all sent CCs. You'll see the CC change in the mapping list.

    4 years ago | 1 comment
  • Gordon Good
    contribution
    1 answer
    2 votes received
    2 votes

    I'd really like to have a way to change the assigned MIDI CC number after it's been assigned by learning. I've built a MIDI controller that sends two CC values (pitch and roll) based on accelerometer values at the same time (e.g. consecutive MIDI messages). Live only remembers the last message sent in its MIDI mappings. If I could just edit the CC number, it would be very easy to make this work.

    Yes, I could rewrite the firmware for my controller to have a special mode that constrains it to sending CC values corresponding to one range of motion. I'd rather not.

    2 years ago | 0 comments
  • saucerx
    contribution
    1 answer
    2 votes received
    2 votes

    Hmm... this seems like quite an oversight - I hope this can be rectified. In my case, I have been experimenting with some motion controllers (such as Leap) and they are notoriously innaccurate and very difficult to get a precise midi value when you are setting up your Midi map. Typing in values in Live (as you can do with the Midi controller software such as Geco) would seem a much needed option.

    1 year ago | 0 comments
  • sounddesignandbrands
    contribution
    1 answer
    2 votes received
    2 votes

    Same here - I think that really is a crucial feature when working with MIDI...

    1 year ago | 0 comments
  • mattgilbert
    contribution
    1 answer
    2 votes received
    2 votes

    I'd also like to see this simple feature added in.

    1 year ago | 0 comments
  • nezzyidy
    contribution
    1 answer
    2 votes received
    2 votes

    Agreed!

    11 months ago | 0 comments
  • stuartm
    contribution
    3 answers
    19 votes received
    1 vote

    Manual editing of the assigned CC value is not possible.

    But a tip for the XY assigning itself:

    move your finger / the stick along the outer edge of the control area while pushing towards the edge, i.e when assigning the x-axis, push your finger to the top end and move it sideways. This should prevent you from "acidentally" sending the other axis' CC. Works very well on my Remote SL.

    4 years ago | 0 comments
  • assemblyline
    contribution
    3 answers
    3 votes received
    1 vote

    +1!!!!

    10 months ago | 0 comments
  • RonForger
    contribution
    1 answer
    1 vote received
    1 vote

    +1
    Yes, that's definititely a required feature in Live 9, as many many plugins have fixed their internal CC mapping : Ableton Live should be able to allow us to set custom CC Mappings (per plugin), thus helping us dealing with "too-rigid" plugins !

    Plugins are too rigid ? Ok, SO the HOST has to be fluid !

    Live has to be Fluid, not rigid !

    7 months ago | 0 comments
  • ultraplay
    contribution
    1 answer
    1 vote received
    1 vote

    Agreed. Why doesn't Ableton sort this out?

    5 months ago | 0 comments
  • docljunior
    contribution
    1 answer
    1 vote received
    1 vote

    Hey guys!
    Came over this:

    Did not solve my problem, but maybe one of yours?

    3 months ago | 0 comments

You need to be logged in, have a Live license, and have a username set in your account to be able to answer questions.

Answers is a new product and we'd like to hear your wishes, problems or ideas.