Controlling more than 8 parameters using User Remote Scripts

Hi, using a script i found in an old forum post I have managed to access banks of parameters other than the "best of bank" using the UC33e.

Currently in my setup the top row of pots control the 8 parameters of the selected bank and the bottom two rows control sends for the first 8 channels.

Is it possible to control further banks using the bottom two rows of pots? So three banks would be accesible at the same time without scrolling through?

If not.. Is there a way I can select the next 8 channels to control the sends on, as currently I can only control the sends on first 8 tracks in a live set?

Thanks in advance.

(link to original post https://forum.ableton.com/viewtopic.php?f=2&t=160308)

The script uses Global Channel 1, Preset 5.

I added sends and button numbers 1 - 8 to select preset bank if it can help anyone else..

# Config File for User-defined Instant Mappings

# We assume that the controls on your MIDI controller
# send CCs (except for pads). All controls that do not have
# an explicit channel setting are expected to use the
# global channel. CCs & Notes are counted from 0-127
# and channels from 0-15.

[Globals]
# The channel that the controller should send on
GlobalChannel: 0
# If your controller is connected via USB, replace ControllerName
# with the name of the respective port. Live will then try to
# recognize the ports for you when you select your Instant-Mappings
InputName: UC-33 USB MIDI Controlle In [1]
OutputName: UC-33 USB MIDI Controll Out [1]
# If your controller has pads that send notes, you can use them to
# play the visible pads in your DrumRacks. Just replace the -1 for
# the note (and channel) of the respective pad. The arrangement of
# the pads in the DrumRacks is as follows:
# 1 2 3 4
# 5 6 7 8
# 9 10 11 12
# 13 14 15 16
# (If you leave the channel of a pad at -1, Live will assume that
# the pad uses the global channel)
Pad1Note: -1
Pad2Note: -1
Pad3Note: -1
Pad4Note: -1
Pad5Note: -1
Pad6Note: -1
Pad7Note: -1
Pad8Note: -1
Pad9Note: -1
Pad10Note: -1
Pad11Note: -1
Pad12Note: -1
Pad13Note: -1
Pad14Note: -1
Pad15Note: -1
Pad16Note: -1
Pad1Channel: -1
Pad2Channel: -1
Pad3Channel: -1
Pad4Channel: -1
Pad5Channel: -1
Pad6Channel: -1
Pad7Channel: -1
Pad8Channel: -1
Pad9Channel: -1
Pad10Channel: -1
Pad11Channel: -1
Pad12Channel: -1
Pad13Channel: -1
Pad14Channel: -1
Pad15Channel: -1
Pad16Channel: -1

[DeviceControls]
# The Encoders will control the device parameters (you can also
# use knobs or sliders). Replace the -1's with the CCs sent by
# the respective controls on your controller. You can also set
# the channel for each controller if it differs from the global
# channel (if you leave the channel of an encoder at -1, Live
# will assume that the encoder uses the global channel).
Encoder1: 57
Encoder2: 76
Encoder3: 74
Encoder4: 71
Encoder5: 14
Encoder6: 15
Encoder7: 26
Encoder8: 31
EncoderChannel1: -1
EncoderChannel2: -1
EncoderChannel3: -1
EncoderChannel4: -1
EncoderChannel5: -1
EncoderChannel6: -1
EncoderChannel7: -1
EncoderChannel8: -1
# Enter the respective map mode for the encoders here. The following
# map modes are available:
# - Absolute
# - Absolute14Bit
# - LinearSignedBit
# - LinearSignedBit2
# - LinearTwoCompliment
# - LinearBinaryOffset
# - AccelSignedBit
# - AccelSignedBit2
# - AccelTwoCompliment
# - AccelBinaryOffset
# Consult the controller's documentation to find out which mode to use.
EncoderMapMode: Absolute
# Buttons used here are expected to not be toggles (i.e., sending
# value 0 every second time you press it).
Bank1Button: 41
Bank2Button: 95
Bank3Button: 19
Bank4Button: 75
Bank5Button: 82
Bank6Button: 77
Bank7Button: 54
Bank8Button: 80
NextBankButton: 61
PrevBankButton: 60
LockButton: -1

[MixerControls]
# Again enter the appropriate CCs for the respective controls.
# If all sliders use the global channel to send their data,
# you can leave the channels at -1. You can, of course, use
# encoders or knobs instead of sliders.
VolumeSlider1: -1
VolumeSlider2: -1
VolumeSlider3: -1
VolumeSlider4: -1
VolumeSlider5: -1
VolumeSlider6: -1
VolumeSlider7: -1
VolumeSlider8: -1
Slider1Channel: -1
Slider2Channel: -1
Slider3Channel: -1
Slider4Channel: -1
Slider5Channel: -1
Slider6Channel: -1
Slider7Channel: -1
Slider8Channel: -1
MasterVolumeSlider: -1
MasterSliderChannel: -1
Send1Knob1: 58
Send1Knob2: 55
Send1Knob3: 79
Send1Knob4: 78
Send1Knob5: 16
Send1Knob6: 17
Send1Knob7: 18
Send1Knob8: 40
Send2Knob1: 43
Send2Knob2: 42
Send2Knob3: 44
Send2Knob4: 21
Send2Knob5: 92
Send2Knob6: 93
Send2Knob7: 86
Send2Knob8: 102
TrackArmButton1: -1
TrackArmButton2: -1
TrackArmButton3: -1
TrackArmButton4: -1
TrackArmButton5: -1
TrackArmButton6: -1
TrackArmButton7: -1
TrackArmButton8: -1
VolumeMapMode: Absolute
SendsMapMode: Absolute

[TransportControls]
# The transport buttons are also expected not to be toggles.
StopButton: -1
PlayButton: -1
RecButton: -1
LoopButton: -1
RwdButton: -1
FfwdButton: -1

One follower

Rich2287 1 year ago | 0 comments

You need to be logged in, have a Live license, and have a username set in your account to be able to answer questions.

Answers is a new product and we'd like to hear your wishes, problems or ideas.